国产精品久久久久久久裸模,搜索欧美一级黄色片,性夜夜久久久夜,国产91在线99

Welcome to the official website of TAT Electronics Co.,Ltd 

24-hour service hotline:075582370515
How to use electromagnetic passive buzzers correctly
Classification:Industry News Release time:2023-11-08 19:21:49
The principle of electromagnetic passive buzzer is a type of electro-acoustic device that converts electrical energy into vibration of vibrating plates through electromagnetic effects to produce sound...

The following is the correct usage method for electromagnetic passive buzzers for users to refer to during design.

The principle of an electromagnetic passive buzzer is an electro-acoustic device that converts electrical energy into vibration of a vibrating plate through electromagnetic effects to produce sound. When a certain frequency of electrical signal passes through the internal coil of the buzzer, an alternating magnetic field is generated. After strengthening the magnetic field through the iron core bracket in the middle of the coil, the vibrating plate on the magnetic coil is pushed to vibrate. The internal structural anatomy diagram is shown in Figure 1; For detailed principles, please refer to electroacoustic knowledge>>>The working principle of electromagnetic passive buzzers

1(23).jpg

The working parameters of a general electromagnetic passive buzzer mainly include coil resistance, rated voltage, SPL value, consumed current, voltage operating range, etc.

It is very important for users to match parameters during use. Here are some examples to illustrate how to achieve parameter matching:

For example, you have chosen to use the FHD-BM1290-0520-42 buzzer; Firstly, we know that the rated voltage of this buzzer is 5Vo-p, the input frequency is 2000Hz, the DC resistance of the coil is 42 ohms, and the SPL value used under rated conditions is at least 85dB. The testing distance is 10cm, the consumption current is not more than 70mA, and the voltage working range is 3-7V;

When using this buzzer, the circuit design must meet the following conditions:

1. The optimal signal frequency for the input buzzer is 2000Hz. Generally, the signal frequency output by PCB boards with CPU clock signals is relatively accurate; But if there is a significant frequency error in the output signal of your PCB board, please pay attention to one principle: first, try to control the frequency error range of the output signal within 100Hz as much as possible; Secondly, the frequency error design value should have an upper tolerance, which means that there should not be a frequency below 2000Hz. The design frequency can be increased from 2000Hz to 2100Hz, which basically does not affect normal use. When inputting a frequency below 2000Hz into the buzzer, some of the buzzers will become very quiet (this is caused by the normal error of the buzzer's starting point and is inevitable). However, when inputting a frequency above 2000Hz, Due to the fact that the starting point of the buzzer at the factory is not greater than 2000Hz, and any frequency signal exceeding the starting point of the buzzer can cause the buzzer to vibrate, it will not make a small sound. However, when the frequency exceeds 2000Hz, the SPL value of some products will decrease slightly (generally within 5dB, the listening sensation will not be too obvious); If your circuit cannot meet the above requirements, you must use a customized buzzer;

2. The signal voltage of the input buzzer must be correct. This voltage is the voltage of the amplifier part pushed by the buzzer in Figure 2, not the total voltage of the PCB circuit


3(1).jpg

3. The amplifier part that drives the buzzer to work is shown in Figure 2. The transistor 2SC3199 must be saturated and conductive, that is, the input signal of the amplifier must be sufficient to drive the transistor to be saturated and conductive. Usually, the value of resistance R1 in the circuit can be adjusted to meet this requirement;

4. There is no special requirement to replace the value of resistor R2 with 0 ohms in Figure 2. Some users must use a current limiting resistor for overall current limiting protection. It is also best to use a resistor below 42 ohms for R2 value. After using a current limiting resistor, the SPL value of the buzzer will decrease slightly, and the value of the reduced sound usually does not exceed 5dB;

5. The working voltage range is 3-7V. SPL values below 5V will be appropriately reduced, while SPL values above 5V will be appropriately increased. Users can test the actual SPL values during actual use. SPL values below 3V can also be used, but will decrease significantly.


少妇人妻一区在线| 久久精品a亚州国产AV| 午夜国产理论电影| 最爱五月婷婷| 国产丝袜91久久久久久久久| 婷婷夜色| 久日韩久久电影| 成人不卡网在线| 91av免费看| 午夜福利亚洲成人| 刚产日韩欧美精品在线| 亚洲 欧美 国产 小说| 亚洲美女髙潮久久久久久!| 欧美美女自慰| 日本成人影片久久| 国产一区二区三区精品电影| 中文字幕乱偷一区二区| 日韩久久久久av电影| 亚洲小黄书无码| 色悠悠国产在线| 腿在移动成人电影| 青青草AV不卡网| www一区二区三区www| 曰本本道不卡视频一| 欧美与男人欧美女人日逼爽欧美精品| 成人色欲17C| 国产久久88综合| 亚洲色图人妻中文字幕黑丝口爆| 亚洲不卡一区三区三州医院| 欧美亚洲人妻中文字幕| 成人大香蕉| 欧美日韩不卡最新视频| 国产亚洲欧美精品久久久| 大地资源网在线观看免费| 精品一区在线观看你懂的| 久久国产精品无码一区成人毛片| 秘 无码一区二区在线| 图片亚洲欧美一区| 就去 国产 日韩 欧美| 日韩日逼片五十路| 操骚逼的免费视频|