国产精品久久久久久久裸模,搜索欧美一级黄色片,性夜夜久久久夜,国产91在线99

歡迎光臨深圳市銳創達電子有限公司官網
24小時服務熱線:075582370515
EM9767.JPG
  • EM9767.JPG
  • DSC_1493_exposure.JPG

M9767

零件應在一個條件下(溫度:5~35℃,濕度:45%~85%R.H.,大氣壓:860~1060hPa)進行測量,除非調節標準條件(溫度:25±3℃,濕度為60±10%R.H.大氣壓:860~1060hPa)來進行測量。

1.Scope

    The specifications should be applied to electret condenser microphone of DGOB4015DD(-P)C1033

2.Storage And Judgement Conditions


Temperature Range(°C)

Rel. Humidity(%)

Static Pressure(kPa)

Judgement

 19~21

 6070 

      86~106

Storage

-4080 



Operating

          -20~70



3.Specifications

    Test Conditions:VS=2.0V,RL=2.2KΩ,Temp=20±2°C, R.H=60±5%

ITEM

Symbol

Test Conditions

Min

Standard

Max

Unit

Sensitivity

  S

f=1KHz,

S.P.L=1Pa

-40

-38

-36

   dB

0dB=1V/Pa

Impedance

  Z

f=1KHz,

S.P.L=1μBar



2.2

Directivity

                  Omni-directional

Current  Consumption

  I


50


500

μA

Operation Voltage Range

  VS


1.0

4.5

10

V

S/N Ratio

 S/N(A)

f=1KHz,S.P.L=1Pa

A Curve

55



dB

Decreacing Voltage Characteristic

  △S

f=1KHz,S.P.L=1Pa

VS=1.5-1.0V



-3

dB

Max.Input Sound Level

 MISPL

f=1KHz,

Distortion≤3%



115

dB


4.Frequency Response

1(1).png

5.APPEARANCE & DIMENSIONS

2(1).png

6.Test Circuit

Measurement Circuit

Vs:Source Voltage 4.5V   RL:Load Resistance 2.2

  

  3(1).png

7.Test Setup Drawing

4(2).jpg

Vs=4.5V

RL=2.2kΩ


8.  Reliability Test

  

  All tests should be done after 2 hours of conditioning at 20,R.H65% ,while the sensitivity is to be within ±3dB from the initial sensitivity after the following experiments.  


8.1  High Temperature Test

      High temperature:                                      +60

        Duration:                                             72 hours

8.2   Low Temperature Test

      Low temperature:                                       -40

        Duration:                                             72 hours

8.3   Temperature Cycle Test (See in Fig.1)

      Low temperature:                                       -25          

        High temperature:                                       +60

        Changeover time:                                       10min

        Duration:                                               30min          

        Cycle:                                                  32

 

8.4   Statical Humidity Test

      Temperature:                                           +40 

        Relative humidity:                                       9095%

        Duration:                                               72hours     


8.5  Vibration Test

     Amplitude :                                             1.52mm

       Duration:                                               1minutes /plane

       Freq.range:                                              1055 Hz

       Total time:                                               2 hours

8.6   Dropping Test

       Drop a unit unpacked onto a board of 20mm thick.

  

        Height:                                                  1.0 m

        Cycle:                                                   6      

8.7   ESD Test

       The microphone under test must be discharged between each ESD exposure without ground.

          (contact:±6KV,air:±8KV)There is no interference in operation after 10 times exposure.

 9.   Regarding the Soldering operation

        a.  Use 15~ 20W soldering iron and maintain 290~310 in operation.

        b.  Operators who work in the solder fixture and the soldering iron must be statically grounded                    

            under each soldering process.

        C.  Soldering should be accomplished within two seconds at each terminal so as not to be overheated.

        d .  Optimal design for heat sink pad is same as below.

5(1).png


10. List and Structure of Materials

6(1).png

NO.

Part name

Material Type

Qty

Origin

Manufacture

Remarks

1

PCB

FR-1

1




2

Holder

ABS

1




3

FET

K596

1




4

Back plate

Cu

1




5

Spacer

Mylar

1




6

Film

FEP

1




7

Outer most shell

AL

1




8

Protection fleece

Fabrics

1




9

Capacitor

0603 10pF

1




1Assembly process

   a)、After connector and holder are once disassembled , they should not be re-used.

   b)、Do not touch outer springs directly(except for PCB or proper terminal set at nominal height.

   c)、Do not give any mechanical shocks to the micphone(e.g. dropping to floor)

2、General information

  2-1: This microphone shall not be operated or stored in following environment.

     >where liquid(water,solvent and so on)splashes.

     >where the air has a high concentration of corrosive gas .

     >where is too dusty.

     >where temperature changes rapidly.

  2-2: Frequency response especially in high frequency region is dependent on the structure of enclosure.

   Please remove additional acoustic mass or cavity in front of the microphone to the utmost.

  2-3:do not put mechanical pressure more than 2 kg to the microphone.

  2-4: microphone should not be in state of outgoing packing for a long-term storage.

  2-5: all the soldering procedures upon microphone must be complete in a metallic device,the temperature of the soldering irons must be limited as 320 and less 3 s ,the operators、the solder fixtures and the soldering irons must be statically grounded under each soldering process.


上一個: M9745P
下一個: 沒有了
久久久五月天婷| 无码人妻久久| 欧美乱色激情久久| 色2019永久网站| 国产精品都市伦理| 婷婷五月天亚洲一二三| 久久久7精品视频| 久久久久久久久久久美女少妇诱惑| 欧美视频日韩视频在线观看视频| 天堂亚洲精品观看| 欧日韩精品视频一| 看片 av一区二区三区| 久久狠狠网站| 久久精品 vip| 日韩人妻一区二区三区99| 麻豆国产91 在线播放小水水| 就要日骚逼视频| 亚洲欧美乱在线视频| 少妇AV在试| 91后入网站视频不卡在线观看高清| 中日不卡AV二区| 亚洲人妻无码视频| 婷婷诱惑在线观看| 中文av一二三区日韩| 久久青青AV| 天天综合网精品亚洲| 一区二区三区在线麻豆| 亚洲一区二区理伦电影片| 国产Av情景剧女教师| 欧美午夜三级福利小视频| 精品久久久夜夜夜| 国产欧美亚洲成人在线| 亚洲很湿很黄很湿很湿很黄的视频| 亚洲欧洲91一区二区| 精品国产大片久久久久久久久| 日韩图片欧美图片日韩一级欧美一级| 外国精品在线观看虐待一卡二卡黄| 色综合啪啪啪| 亚洲色欲亚洲色欲亚洲色欲 | 婬荡的富婆一区二区| 五月九九欧美狠狠丁香久久综合激情|