国产精品久久久久久久裸模,搜索欧美一级黄色片,性夜夜久久久夜,国产91在线99

歡迎光臨深圳市銳創達電子有限公司官網
24小時服務熱線:075582370515
M6050-2.jpg
  • M6050-2.jpg
  • M6050-1(1).jpg
  • M6050-4.jpg
  • M6050-3.jpg

M6050

零件應在一個條件下(溫度:5~35℃,濕度:45%~85%R.H.,大氣壓:860~1060hPa)進行測量,除非調節標準條件(溫度:25±3℃,濕度為60±10%R.H.大氣壓:860~1060hPa)來進行測量。

1.Scope

    The specifications should be applied to electret condenser microphone of DGO6050CD(-P)

2.Storage And Judgement Conditions

             Temperature Range(°C)Rel. Humidity(%)Static Pressure(kPa)Judgement  19~21 60~70       86~106 Storage -30~70   Operating         -20~60  

3.Specifications

    Test Conditions:VS=4.5V,RL=2.2KΩ,Temp=20±2°C, R.H=60±5%

ITEMSymbolTest ConditionsMinStandardMaxUnitSensitivity  Sf=1KHz,S.P.L=1Pa-54-52-50   dB0dB=1V/PaImpedance  Zf=1KHz,S.P.L=1Pa  2.2KΩDirectivity                  Omni-directionalCurrent  Consumption  I 50 500μAOperation Voltage Range   VS 1.04.510VS/N Ratio S/N(A)f=1KHz,S.P.L=1PaA Curve55  dBDecreacing Voltage Characteristic  △Sf=1KHz,S.P.L=1PaVS=4.5-3.0V  -3dBMax.Input Sound Level MISPLf=1KHz,Distortion<3%  110dB

4.Frequency Response

     1(17).png

2(16).png 

 


 

6.Test Circuit

 

   Measurement CircuitVs:Source Voltage 4.5V   RL:Load Resistance 2.2KΩ                                       

 3(15).png

 

7.Test Setup Drawing


 


7(1).png4.jpg


 

 

 

 

8.  Reliability Test

  

  All tests should be done after 2 hours of conditioning at 20,R.H65% ,while the sensitivity is to be within ±3dB from the initial sensitivity after the following experiments.   

 

8.1  High Temperature Test

      High temperature:                                      +80

        Duration:                                             72 hours

8.2   Low Temperature Test

      Low temperature:                                       -40

        Duration:                                             72 hours

8.3   Temperature Cycle Test (See in Fig.1)

      Low temperature:                                       -40          

        High temperature:                                       +80

        Changeover time:                                       10min

        Duration:                                               30min          

        Cycle:                                                  32

 

8.4   Statical Humidity Test

      Temperature:                                           +40 

        Relative humidity:                                       9095%

        Duration:                                               72hours      

 

 

8.5  Vibration Test

     Amplitude :                                             1.52mm

       Duration:                                               1minutes /plane

       Freq.range:                                              1055 Hz

       Total time:                                               2 hours

8.6   Dropping Test

       Drop a unit unpacked onto a board of 20mm thick.

  

        Height:                                                  1.0 m

        Cycle:                                                   6      

 

 9.   Regarding the Soldering operation

        a.  Use 25~ 30W soldering iron and maintain 310~330 in operation.

        b.  Operators who work in the solder fixture and the soldering iron must be statically grounded                    

            under each soldering process.

        C.  Soldering should be accomplished within two seconds at each terminal so as not to be overheated.

        d .  Optimal design for heat sink pad is same as below.

       

 

           5(12).png

6(1).jpg


NO.

Part name

Material Type

Qty

Origin

Manufacture

Remarks

1

PCB

FR-4

1




2

FET

K596

1




3

Holder

POM

1




4

Back plate

Cu

1




5

Spacer

Mylar

1




6

Film

FEP

1




7

Outer most shell

AL

1




8

Cloth

Fabrics

1




 

10、Assembly process

   a)、After connector and holder are once disassembled , they should not be re-used.

   b)、Do not touch outer springs directly(except for PCB or proper terminal set at nominal height.

   c)Do not give any mechanical shocks to the micphone(e.g. dropping to floor)

 

11、General information

  11-1: This microphone shall not be operated or stored in following environment.

     >where liquid(water,solvent and so on)splashes.

     >where the air has a high concentration of corrosive gas .

     >where is too dusty.

     >where temperature changes rapidly.

 

  11-2: Frequency response especially in high frequency region is dependent on the structure of enclosure.

 

   Please remove additional acoustic mass or cavity in front of the microphone to the utmost.

 

  12-3:do not put mechanical pressure more than 2 kg to the microphone.

 

  13-4: microphone should not be in state of outgoing packing for a long-term storage.

 

  14-5: all the soldering procedures upon microphone must be complete in a metallic device,the temperature of the soldering irons must be limited as 320 and less 3 s ,the operators、the solder fixtures and the soldering irons must be statically grounded under each soldering process.


上一個: M6027W40
下一個: M9745
中文字幕午夜电影亚洲| 成人黄色99AV| 欧美成人日韩精品老金| 欧美ww日韩www| 69国产一区二区| 亚洲日韩中文字幕在线一区二区| 亚洲国产精品久久66| 欧美大鸡把猛操视频在线播放| 久久久久久久久久黄色电影网址| 日本人妻精品一区二区三区久久久| 91精品久色蜜桃| 狠狠88综合娱乐久久久久| 激情久久伦理精品| 国产美女主播自拍| www.熟女| 麻豆欧美美女自慰高清网站| 欧美后入三级| 亚洲日韩欧美久久| 最近国语视频在线观看免费播放| 精品电影日本新娘交换精品久久| 草毕网站在线看| 精选91久久999| AV无码打桩机| 国产99日本精品| 国产精品 羞羞答答| 日本猛男啪啪啪一区二区三区| 中日韩欧美久久在线| 人妻尝试3p视频| 综合射在线第一页一区| 97久久精品国产一区二区蜜芽| 欧美日本一区二区三区视频| 久久久久久午夜噜噜噜噜蜜臀AV| 综合色 欧美精品| 欧美国产日韩熟女| 久久久九久伦理| 免费日B,视频| 欧美一成乱码不卡一二三区| 有在线免费播放的舔b视频看吗 | 自偷自拍亚洲精品第三页| 亚洲成人原创乱码| 色香蕉视频在线|